Maximum Merlin (pre-2001) Bedienungsanleitung PDF herunterladen

MERLIN

INSTALLATION

PROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR, ELECTRICIAN

OR TELEVISION ANTENNA INSTALLER (CHECK WITH YOUR LOCAL BUILDING SUPPLY, OR HARDWARE STORE

FOR REFERRALS). TO PROMOTE CONFIDENCE, PERFORM A TRIAL WIRING BEFORE INSTALLATION.

When connecting the wind direction sensor

to the Z-mast, make certain that terminal #4

is aligned with the Z-mast arm. If the sensor

is not installed in this manner your wind

direction readings will be incorrect.

Slide the stub masts through the rubber boots and

insert the stub masts into the bottom of the sensors. Secure

with the cotter pins. Coat all wire connections with silicone

sealant and slip the boots over the sensors.

TERMINAL #4

MUST ALIGN

WITH Z-MAST

ARM

TERMINAL

WIND DIRECTION

SENSOR

BOSS

WIND DIRECTION

SENSOR

COTTER

STRAIGHT

STUB MAST

Z-STUB

MAST

RED & GREEN

WIRES

BLACK & WHITE

WIRES

BOOT

WIND SPEED

SENSOR

Feed the terminal lug end of the red and green wires through the other

rubber boot. Connect the red wire to the terminal marked #4.

Connect the green wire to the terminal marked #5. The polarity MUST be

observed. Use the hex nuts provided. (Do NOT adjust the nuts that are

already on the wind direction sensor).

Feed the teminal lug end of the black and white wires through

one of the rubber boots and connect the lugs to the terminals on the

bottom of the wind speed sensor using the brass nuts provided. The polarity

does not matter. (Do NOT adjust the nuts that are already on the sensor).

Determine where you are going to locate both the

rooftop sensors and the read-out.

Samuel Barnett Boulevard

New Bedford, MA 02745

(508) 995-2200

BLACK AND WHITE

WIRES

BOOT

RED

WIRE

GREEN

WIRE

Secure the sensors and stub masts to your antenna mast (not supplied) with

the two hose clamps. Align the wind-direction Z-mast arm to true North.

Radio Shack and similar stores have a selection of tall masts and roof

mounting brackets. Choose a mount that best suits your location and

provides at least eight feet of vertical clearance above objects on the roof.

HOSE

CLAMPS

NORTH

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - INSTALLATION

MERLININSTALLATIONPROPER INSTALLATION IS IMPORTANT. IF YOU NEED ASSISTANCE, CONSULT A CONTRACTOR, ELECTRICIAN OR TELEVISION ANTENNA INSTALLER (CHEC

Seite 2

MERLININSTALLATION(continued)Samuel Barnett BoulevardNew Bedford, MA 02745(508) 995-22006Follow the instructions supplied with the antenna mount and s

Seite 3 - OPERATION

MERLINOPERATIONIMPORTANT FACTS ABOUT YOUR MERLINSamuel Barnett BoulevardNew Bedford, MA 02745(508) 995-2200Resetting the Peak, Average and Forcast fun

Seite 4 - (508) 995-2200

MERLINIMPORTANT FACTS ABOUT YOUR MERLIN (CONT.)Samuel Barnett BoulevardNew Bedford, MA 02745(508) 995-2200Forcast- When first powering up MERLIN, afte

Seite 5 - IF ALL LEDS LIGHT

MERLINTROUBLE SHOOTING(WIND DIRECTION)IF ALL LEDS LIGHT...IF THE INSTRUMENT TESTS OKAY...Samuel Barnett BoulevardNew Bedford, MA 02745(508) 995-

Seite 6 - (WIND SPEED)

MERLINTROUBLE SHOOTING(WIND SPEED)IF THERE IS WIND...IF THERE IS NO WIND...Samuel Barnett BoulevardNew Bedford, MA 02745(508) 995-2200123Disconn

Seite 7

IMPORTANT ADDITIONAL INFORMATION Components: Along with the indicator, the following components are included with this instrument:

Kommentare zu diesen Handbüchern

Keine Kommentare

Maximum Merlin (pre-2001) Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Messgeräte Maximum Merlin (pre-2001) herunter. Maximum Merlin (pre-2001) User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messgeräte Maximum Merlin (pre-2001)